Replacement ASUS X550DP 40pin LED 1422-01G9000 LCD Cable

Q: Is this LCD cable for a touchscreen or standard (non‑touch) screen?

This cable is designed for a standard screen. Touchscreen and non‑touch cables are not interchangeable – here is why: Touchscreen cables have additional pins/lines for the digitizer (touch sensor) data transmission, typically using a separate I²C or USB interface. Non‑touch (standard) cables only carry video signals (eDP or LVDS) and backlight power – they lack the extra pins for touch data. Connecting a non‑touch cable to a touchscreen will result in no touch functionality. Conversely, using a touchscreen cable on a standard screen may cause display issues or interference. How to verify your screen type: Check your laptop's specifications online, look at the original cable's connector – if it has more than 30 pins (for eDP) or extra separate wires, it is likely a touch cable. Also, check the Device Manager under "Human Interface Devices" – if a touchscreen is listed, your screen supports touch. If unsure, contact our support with your laptop's full model number and the part number printed on your original cable.

Q: What are the pin count and pin pitch of this LCD cable?

Pin count: 40 pins | Pin pitch: N/A . These specifications are critical for compatibility: Pin count: The number of pins must match the motherboard and LCD panel connectors exactly. Common counts for eDP cables are 30, 40, or 50 pins. Even one pin missing or extra can prevent the display from working. Pin pitch: The distance between adjacent pins – typically 0.4mm , 0.5mm , or 1.0mm . Using a cable with the wrong pitch (e.g., 0.4mm vs 0.5mm) will cause poor contact, bent pins, or even damage to the motherboard header. You cannot force a different pitch connector – it simply will not fit. Cable length: Must be sufficient to route from the motherboard (usually near the hinge area) through the hinge and up to the LCD panel without tension. Too short and you cannot connect it; too long and you may need to fold it, which can damage the traces. How to check your original cable: Look for printed markings on the cable (e.g., "30P 0.5mm") or measure with a caliper if you have one. You can also count the pins on the connector carefully.

Q: Where is the LCD cable physically located inside the laptop, and how is it routed?

The LCD cable connects the motherboard to the LCD panel inside the screen assembly. Its path includes: Motherboard end: Usually located near the hinge area on the system board, often at the edge of the PCB for easy routing. Look for a header labelled LCD , LVDS , or eDP . Through the hinge: The cable passes through the left or right hinge (or both, for some models) to transition from the base chassis to the lid. This is the most vulnerable section – the cable is flexed every time you open and close the laptop. Up the display lid: Inside the lid, the cable runs along the edge (left or right side) or the back of the panel, secured with tape, to the LCD connector at the bottom or back of the panel. Access requirements: To access the motherboard end: Remove the bottom cover (D‑cover) only. To access the LCD panel end: Remove the screen bezel (B‑cover). Some models require removing the entire display assembly (lid) from the chassis first. The cable is often one of the first components to fail in laptops due to repeated hinge flexing – always inspect the old cable for visible wear at the hinge area.

Complete specifications for reference:
1422-01G9000 Asus A550C A550CA A550CC A550CL A550D A550DP A550EA A550L A550LA A550LB A550LC A550LD A550LN A550V A550VB A550VC ?D551E D551EA D551L D551LB? K550C K550CA K550CC K550D K550DP K550J K550JD K550JK K550L K550LA K550LB K550LC K550LD K550LN K550V K550VB K550VC K550Z K550ZA K550ZE R510C R510CA R510CC R510D R510DP R510E R501EA R510L R510LA R510LB R510LC R510LD R510LN R510V R510VB R510VC X550C X550CA X550CC X550CL X550D X550DP X550E X550EA X550J X550JD X550JK X550L X550LA X550LB X550LC X550LD X550LN X550LNV X550M X550MD X550V X550VA X550VB X550VC X550VL X550W X550WA X550WE X550Z X550ZA

Video Connector — FFC Cable

Frequently Asked Questions & Solutions

Is this LCD cable for a touchscreen or standard (non‑touch) screen?

This cable is designed for a standard screen. Touchscreen and non‑touch cables are not interchangeable – here is why:

Touchscreen cables have additional pins/lines for the digitizer (touch sensor) data transmission, typically using a separate I²C or USB interface.
Non‑touch (standard) cables only carry video signals (eDP or LVDS) and backlight power – they lack the extra pins for touch data.
Connecting a non‑touch cable to a touchscreen will result in no touch functionality. Conversely, using a touchscreen cable on a standard screen may cause display issues or interference.

How to verify your screen type: Check your laptop's specifications online, look at the original cable's connector – if it has more than 30 pins (for eDP) or extra separate wires, it is likely a touch cable. Also, check the Device Manager under "Human Interface Devices" – if a touchscreen is listed, your screen supports touch.

If unsure, contact our support with your laptop's full model number and the part number printed on your original cable.

What are the pin count and pin pitch of this LCD cable?

Pin count: 40 pins | Pin pitch: N/A.

These specifications are critical for compatibility:

Pin count: The number of pins must match the motherboard and LCD panel connectors exactly. Common counts for eDP cables are 30, 40, or 50 pins. Even one pin missing or extra can prevent the display from working.
Pin pitch: The distance between adjacent pins – typically 0.4mm, 0.5mm, or 1.0mm. Using a cable with the wrong pitch (e.g., 0.4mm vs 0.5mm) will cause poor contact, bent pins, or even damage to the motherboard header. You cannot force a different pitch connector – it simply will not fit.
Cable length: Must be sufficient to route from the motherboard (usually near the hinge area) through the hinge and up to the LCD panel without tension. Too short and you cannot connect it; too long and you may need to fold it, which can damage the traces.

How to check your original cable: Look for printed markings on the cable (e.g., "30P 0.5mm") or measure with a caliper if you have one. You can also count the pins on the connector carefully.

Does this LCD cable support my screen resolution (e.g., 1080p, 4K, or high refresh rate)?

The cable's bandwidth is determined by its construction – the number of lanes (for eDP) and shielding quality. Here is a general guide:

Standard cables (30‑pin eDP): Typically support up to 1080p (Full HD) at 60Hz. Some may support 144Hz or 4K if designed with higher‑grade materials.
High‑bandwidth cables (40‑pin or 50‑pin eDP): Required for 4K (UHD) screens or high refresh rates (120Hz, 144Hz, 240Hz). These have more data lanes.
LVDS cables (older laptops): Support lower resolutions – usually up to 1600x900 or 1920x1080 at 60Hz.

Important: The cable must match the part number of your original cable or be listed as a compatible alternative. Using an incompatible cable may result in:

No display (black screen)
Flickering or artifacts
Limited resolution (e.g., 1080p cable on a 4K screen will only show 1080p)
Intermittent signal loss

Always refer to the cable's specifications and compare with your laptop's service manual.

How to replace the LCD cable step by step?

Safety first: Disconnect the battery and AC adapter to avoid electrical shorts.
Remove the bottom cover (D‑cover) to access the motherboard – the LCD cable usually connects to a header near the hinge area.
Remove the screen bezel (B‑cover) – carefully pry it off starting from the inner edge, using a plastic spudger to avoid damage. The bezel is often held by clips and/or adhesive.
Disconnect the old cable from the LCD panel – locate the connector on the back of the screen (or at the bottom edge). Flip up the ZIF locking tab (if present) and gently slide the cable out.
Disconnect the old cable from the motherboard – find the header, usually labelled LCD, LVDS, eDP, or J_LCD. Unlock the ZIF tab or gently pull the connector.
Remove the old cable – it runs through the hinge, often taped or clipped to the chassis. Carefully free it without tearing.
Route the new cable exactly along the original path – through the hinge and along the chassis grooves. Secure it with the original tape or clips. Do not pinch the cable in the hinge area – this is a common failure point.
Connect the cable to the motherboard – insert the connector fully (gold contacts facing the locking tab for ZIF), then lock the tab.
Connect the cable to the LCD panel – insert it into the panel connector and lock the ZIF tab.
Test before full reassembly – reconnect the battery, power on the laptop, and check if the display works correctly (no flickering, lines, or artifacts).
Power off, disconnect the battery again, reassemble the bezel (press around the edges to snap clips) and the bottom cover.

Warning: The LCD cable is extremely fragile – avoid sharp bends (especially at 90° angles), and never pull on the cable itself; always hold the connector.

Where is the LCD cable physically located inside the laptop, and how is it routed?

The LCD cable connects the motherboard to the LCD panel inside the screen assembly. Its path includes:

Motherboard end: Usually located near the hinge area on the system board, often at the edge of the PCB for easy routing. Look for a header labelled LCD, LVDS, or eDP.
Through the hinge: The cable passes through the left or right hinge (or both, for some models) to transition from the base chassis to the lid. This is the most vulnerable section – the cable is flexed every time you open and close the laptop.
Up the display lid: Inside the lid, the cable runs along the edge (left or right side) or the back of the panel, secured with tape, to the LCD connector at the bottom or back of the panel.

Access requirements:

To access the motherboard end: Remove the bottom cover (D‑cover) only.
To access the LCD panel end: Remove the screen bezel (B‑cover). Some models require removing the entire display assembly (lid) from the chassis first.

The cable is often one of the first components to fail in laptops due to repeated hinge flexing – always inspect the old cable for visible wear at the hinge area.

How do I identify the motherboard header for the LCD cable and connect it correctly?

The motherboard header for the LCD cable is usually clearly labelled. Common silk‑screen markings include:

LCD / LCD1 / J_LCD
LVDS / J_LVDS (for older LVDS cables)
eDP / eDP1 (for modern Embedded DisplayPort cables)
DISP / J_DISP

Connection steps:

If the motherboard connector is a ZIF (Zero Insertion Force) type (most common), lift the small locking flap, insert the cable with the exposed copper contacts facing the flap, then press the flap down to lock.
If it is a standard plug‑in type (less common for LCD cables), align the key (notch) and push gently until fully seated.
Some cables have a reinforced pull‑tab – use this to handle the cable, not the body itself.
There is usually a blue or red stripe on one edge of the cable – this should align with the "pin 1" indicator (a small triangle or dot) on the motherboard header.

Do not force the connector – if it does not go in easily, check orientation and ensure no pins are bent.

What precautions should I take, and what if there is no display, flickering, or lines after replacement?

Critical precautions:

Always disconnect the battery before handling the LCD cable – even a small short can damage the graphics chip or backlight circuit.
Handle the cable with extreme care – it is the most fragile cable in the laptop. Avoid sharp bends, creasing, and folding. The hinge area is especially susceptible – route it exactly as the original.
Do not overtighten the bezel screws – this can pinch the cable if it is not seated properly in its channel.
Use anti‑static precautions – ground yourself before touching connectors to prevent ESD damage to the panel or motherboard.
Ensure the cable is fully seated at both ends – a partially inserted cable can cause intermittent display issues.

Troubleshooting if the display does not work after installation:

No display / black screen: Re‑check both connections – reseat the cable at the motherboard and the LCD panel. Ensure the ZIF tabs are locked.
Flickering or intermittent display: Check the cable routing – it may be pinched in the hinge or touching a heat source. Try re‑routing it more carefully.
Lines, artifacts, or distorted colours: This often indicates a poor connection or a damaged cable. Inspect the connector pins for bent or broken contacts. Also verify that the cable is correctly oriented (pin 1 alignment).
Partial display (some areas blank): The cable may be damaged – try re‑seating it. If the issue persists, the cable itself may be defective.
Backlight works but no image: The data lines may be faulty – check the motherboard header for bent pins.
Touchscreen not responding (for touch models): Verify that the cable is a touch‑compatible version – it has extra pins for the digitizer.

Quick diagnostic tip: If you have access to an external monitor, connect it to the laptop. If the external display works correctly, the issue is likely the LCD cable or the panel itself. If external display also has issues, the graphics chip or motherboard may be the problem.

If the problem persists, contact our support with your laptop model and the exact part number of your original cable.

LCD video signal cable for ASUS X550DP 40pin LED 1422-01G9000